Important: Use custom search function to get better results from our thousands of pages

Use " " for compulsory search eg:"electronics seminar" , use -" " for filter something eg: "electronics seminar" -"/tag/" (used for exclude results from tag pages)


Tags: automatic room li, automatic room light controller with bidirectional visitor counterautomatic room light control system, automatic room light controller project report, automatic room light controller with visitor counter using microcontroller, automatic room light controller with visitor counter at89s52automatic room light controller project, automatic room light controller with visitor counter ir sensor, automatic room light controller with visitor counter pptautomatic room light controller circuit,
 
 
Thread Rating:
  • 1 Votes - 5 Average
  • 1
  • 2
  • 3
  • 4
  • 5
AUTOMATIC ROOM LIGHT CONTROLLER WITH BIDIRECTIONAL VISITOR COUNTER
Post: #1
Thumbs Up 

AUTOMATIC ROOM LIGHT CONTROLLER WITH BIDIRECTIONAL VISITOR COUNTER


Introduction


Project Definition:

Project title is “AUTOMATIC ROOM LIGHT CONTROLLER WITH BIDIRECTIONAL VISITOR COUNTER “.

The objective of this project is to make a controller based model to count number of persons visiting particular room and accordingly light up the room. Here we can use sensor and can know present number of persons.

In today’s world, there is a continuous need for automatic appliances with the increase in standard of living, there is a sense of urgency for developing circuits that would ease the complexity of life.

Also if at all one wants to know the number of people present in room so as not to have congestion. This circuit proves to be helpful.

1.2 Project Overview


This Project “Automatic Room Light Controller with Visitor Counter using Microcontroller is a reliable circuit that takes over the task of controlling the room lights as well us counting number of persons/ visitors in the room very accurately. When somebody enters into the room then the counter is incremented by one and the light in the room will be switched ON and when any one leaves the room then the counter is decremented by one. The light will be only switched OFF until all the persons in the room go out. The total number of persons inside the room is also displayed on the seven segment displays.

The microcontroller does the above job. It receives the signals from the sensors, and this signal is operated under the control of software which is stored in ROM. Microcontroller AT89S52 continuously monitor the Infrared Receivers, When any object pass through the IR Receiver's then the IR Rays falling on the receiver are obstructed , this obstruction is sensed by the Microcontroller.


Attached File(s)
.docx  AUTOMATIC ROOM LIGHT CONTROLLER WITH BIDIRECTIONAL VISITOR COUNTER.docx (Size: 270.2 KB / Downloads: 2083)
Post: #2

.doc  Automatic room light controller with visitor counter.doc (Size: 266.5 KB / Downloads: 689)
Room Light Controller with Visitor Counter

INTRODUCTION
This Project “Automatic Room Light Controller with Visitor Counter using Microcontroller” is a reliable circuit that takes over the task of controlling the room lights as well us counting number of persons/ visitors in the room very accurately. When somebody enters into the room then the counter is incremented by one and the light in the room will be switched ON and when any one leaves the room then the counter is decremented by one. The light will be only switched OFF until all the persons in the room go out. The total number of persons inside the room is also displayed on the seven segment displays. The microcontroller does the above job. It receives the signals from the sensors, and this signal is operated under the control of software which is stored in ROM. Microcontroller AT89S52 continuously monitor the Infrared Receivers, When any object pass through the IR Receiver's then the IR Rays falling on the receivers are obstructed this obstruction is sensed by the Microcontroller.
Post: #3
Star 
[font=Times New Roman][/font]
Post: #4
hi bharat1437,
what you want to say? there is only the title. do you want to know anything more about the topic? then please ask
Post: #5
hi,
we want the program for this project.please if you can send us details like circuit diagram,program,etc
Post: #6
I am working over this project as my minor project!!
I used 89c2051 microcontroller for the same!!
I am new to microcontroller programming so plss help me in C progamming for the same!!
I connected my sensors to P3.0 and P3.1
Transistors are connected to P3.3 and P3.4 in order to connect two 7-segment displays
And connection of 7-segment display is like-
pin 'a' to P1.1;
pin 'b' to P1.2;
.
.
pin 'g' to P1.7

Plss help me as soon as you can
My id is somani_paresh[at]yahoo.co.in
Post: #7
am working on the same but using pic microcontrollers.want to use infrared sensors any help on circuit diagrams
Post: #8
To get more information about the topic " Mechanical Engineering Project Ideas List" please refer the link below

http://project-seminars.com/Thread-mecha...ist?page=7

http://project-seminars.com/Thread-mecha...rts-titles
Post: #9
To get more information about the topic "AUTOMATIC ROOM LIGHT CONTROLLER WITH BIDIRECTIONAL VISITOR COUNTER " please refer the link below

http://project-seminars.com/Thread-autom...or-counter

http://project-seminars.com/Thread-autom...or-counter

http://project-seminars.com/Thread-autom...ter?page=2

http://project-seminars.com/Thread-autom...th-counter

http://project-seminars.com/Thread-autom...rol-system
Post: #10
plz send synopsis of this project
Post: #11
To get more information about the topic "AUTOMATIC ROOM LIGHT CONTROLLER WITH BIDIRECTIONAL VISITOR COUNTER " please refer the link below

http://project-seminars.com/Thread-autom...or-counter

http://project-seminars.com/Thread-autom...or-counter

http://project-seminars.com/Thread-autom...ter?page=2

http://project-seminars.com/Thread-autom...th-counter

http://project-seminars.com/Thread-autom...rol-system
Post: #12
send me detail description of project on automatic room light control
Post: #13
to get information about the topic "AUTOMATIC ROOM LIGHT CONTROLLER WITH VISITOR COUNTER" full report ppt and related topic refer the link bellow

http://project-seminars.com/Thread-autom...ter?page=2

http://project-seminars.com/Thread-autom...or-counter
Post: #14
AUTOMATIC ROOM LIGHT CONTROLLER WITH BIDIRECTIONAL VISITOR COUNTER


.docx  AUTOMATIC ROOM LIGHT CONTROLLER.docx (Size: 161.08 KB / Downloads: 31)
CIRCUIT DIAGRAM

The IR transmitter will emit modulated 38 kHz IR signal and at the receiver we use TSOP1738 (Infrared Sensor). The output goes high when the there is an interruption and it return back to low after the time period determined by the capacitor and resistor in the circuit. I.e. around 1 second. CL100 is to trigger the IC555 which is configured as monostable multivibrator. Input is given to the Port 1 of the microcontroller. Port 0 is used for the 7-Segment display purpose. Port 2 is used for the Relay Turn On and Turn off Purpose.LTS 542 (Common Anode) is used for 7-Segment display. And that time Relay will get Voltage and triggered so light will get voltage and it will turn on. And when counter will be 00 that time Relay will be turned off. Reset button will reset the microcontroller.Microcontroller based Visitor Counter.

TRANSMISSION CIRCUIT

This circuit diagram shows how a 555 timer IC is configured to function as a basic monostable multivibrator. A monostable multivibrator is a timing circuit that changes state once triggered, but returns to its original state after a certain time delay. It got its name from the fact that only one of its output states is stable. It is also known as a 'one-shot'.
In this circuit, a negative pulse applied at pin 2 triggers an internal flip-flop that turns off pin 7's discharge transistor, allowing C1 to charge up through
R1. At the same time, the flip-flop brings the output (pin 3) level to 'high'. When capacitor C1 as charged up to about 2/3 Vcc, the flip-flop is triggered once again, this time making the pin 3 output 'low' and turning on pin 7's discharge transistor, which discharges C1 to ground. This circuit, in effect, produces a pulse at pin 3 whose width t is just the product of R1 and C1, i.e., t=R1C1.
IR Transmission circuit is used to generate the modulated 36 kHz IR signal. The IC555 in the transmitter side is to generate 36 kHz square wave. Adjust the preset in the transmitter to get a 38 kHz signal at the o/p. around 1.4K we get a 38 kHz signal. Then you point it over the sensor and its o/p will go low when it senses the IR signal of 38 kHz.
Post: #15
AUTOMATIC ROOM LIGHT CONTROLLER WITH BIDIRECTIONAL VISITOR COUNTER


.docx  ROOM LIGHT CONTROLLER.docx (Size: 270.2 KB / Downloads: 29)

Project Definition:

Project title is “AUTOMATIC ROOM LIGHT CONTROLLER WITH BIDIRECTIONAL VISITOR COUNTER “.
The objective of this project is to make a controller based model to count number of persons visiting particular room and accordingly light up the room. Here we can use sensor and can know present number of persons.
In today’s world, there is a continuous need for automatic appliances with the increase in standard of living, there is a sense of urgency for developing circuits that would ease the complexity of life.
Also if at all one wants to know the number of people present in room so as not to have congestion. This circuit proves to be helpful.

Project Overview

This Project “Automatic Room Light Controller with Visitor Counter using Microcontroller is a reliable circuit that takes over the task of controlling the room lights as well us counting number of persons/ visitors in the room very accurately. When somebody enters into the room then the counter is incremented by one and the light in the room will be switched ON and when any one leaves the room then the counter is decremented by one. The light will be only switched OFF until all the persons in the room go out. The total number of persons inside the room is also displayed on the seven segment displays.
The microcontroller does the above job. It receives the signals from the sensors, and this signal is operated under the control of software which is stored in ROM. Microcontroller AT89S52 continuously monitor the Infrared Receivers, When any object pass through the IR Receiver's then the IR Rays falling on the receiver are obstructed , this obstruction is sensed by the Microcontroller.

Procedure Followed While Designing:

In the beginning I designed the circuit in DIPTRACE software. Dip trace is a circuit designing software. After completion of the designing circuit I prepared the layout.
Then I programmed the microcontroller using KEIL software using hex file.
Then soldering process was done. After completion of the soldering process I tested the circuit.
Still the desired output was not obtained and so troubleshooting was done. In the process of troubleshooting I found the circuit aptly soldered and connected and hence came to conclusion that there was error in programming section which was later rectified and the desired results were obtained.

Microcontroller AT89S52:

The AT89S52 is a low-power, high-performance CMOS 8-bit microcontroller with 8K bytes of in-system programmable Flash memory. The device is manufactured using Atmel’s high-density nonvolatile memory technology and is compatible with the Industry-standard 80C51 instruction set and pin out. The on-chip Flash allows the program memory to be reprogrammed in-system or by a conventional nonvolatile memory pro- grammar. By combining a versatile 8-bit CPU with in-system programmable Flash on a monolithic chip, the Atmel AT89S52 is a powerful microcontroller which provides a highly-flexible and cost-effective solution to many embedded control applications.

Testing And Results

We started our project by making power supply. That is easy for me but when we turn toward the main circuit, there are many problems and issues related to it, which we faced, like component selection, which components is better than other and its feature and cost wise a We started our project by making power supply. That is easy for me but when I turn toward the main circuit, there are many problems and issues related to it, which are I faced, like component selection, which components is better than other and its feature and cost wise also, then refer the data books and other materials related to its.
 

Marked Categories : working of bidirectional visitor counter, 7 automatic room light control, automatic room light controller with bidirectional visitor counter project pdf, automatic room controller, automatic room light controller with bidirectional visitor counter, automatic room light control with bi directional visitor counter, microcontroller based automatic room light control, automatec room light control application, automatec room light control appliction, automatic room light, automatic room light controller with bidirectional visitor counter ppt, automatic room light controller with visitor counter using microcontroller 8051 hex file, ir people counter project,

[-]
Quick Reply
Message
Type your reply to this message here.

Image Verification
Image Verification
(case insensitive)
Please enter the text within the image on the left in to the text box below. This process is used to prevent automated posts.

Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  harnessing light of possibilities and challenges ppt Guest 0 1,101 16-07-2017 12:20 AM
Last Post: Guest
  seminar on uses of light possibilities and challenges pdf Guest 0 184 16-07-2017 12:20 AM
Last Post: Guest
  automatic speed control for vehicle at school zones using ir sensor Guest 0 200 16-07-2017 12:20 AM
Last Post: Guest
  ppt for examination room guide using rfid for jumbling system based exams Guest 0 217 16-07-2017 12:20 AM
Last Post: Guest
  future scope of automatic transformer distribution and load sharing system Guest 0 190 16-07-2017 12:20 AM
Last Post: Guest
  ppt on sensor operated automatic reverse braking system Guest 0 256 16-07-2017 12:20 AM
Last Post: Guest
  advantages of automatic light dim and dip controller Guest 0 234 16-07-2017 12:20 AM
Last Post: Guest
  89c51 microcontroller program for automation of street light system Guest 0 157 16-07-2017 12:20 AM
Last Post: Guest
  leap motion controller seminar pdf Guest 0 241 16-07-2017 12:20 AM
Last Post: Guest
  automatic vegetable or lemon cutting machine pdf Guest 0 340 16-07-2017 12:20 AM
Last Post: Guest
This Page May Contain What is AUTOMATIC ROOM LIGHT CONTROLLER WITH BIDIRECTIONAL VISITOR COUNTER And Latest Information/News About AUTOMATIC ROOM LIGHT CONTROLLER WITH BIDIRECTIONAL VISITOR COUNTER ,If Not ...Use Search to get more info about AUTOMATIC ROOM LIGHT CONTROLLER WITH BIDIRECTIONAL VISITOR COUNTER Or Ask Here

Options: