Important: Use custom search function to get better results from our thousands of pages

Use " " for compulsory search eg:"electronics seminar" , use -" " for filter something eg: "electronics seminar" -"/tag/" (used for exclude results from tag pages)


 
 
Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Cryogenic cooling in machining processes
Post: #1

Presented by: Kulkarni Aniket P.



.pptx  10TH08F-Cryogenic cooling in machining processes.pptx (Size: 91.06 KB / Downloads: 195)

Introduction
The cooling applications in machining operations play a very important role and many operations cannot be carried out efficiently without cooling.
Application of a coolant in a cutting process can increase tool life and dimensional accuracy, decrease cutting temperatures, surface roughness and the amount of power consumed in a metal cutting process .
Thus, it become mandatory to use coolant in machining operations.

Cutting fluids i.e. coolants
There are two categories
i)Conventional cutting fluids.
a)Water soluble cutting fluids
b)Mineral oils

ii)Cryogenic cutting fluids.
Here, liquid nitrogen is used as a cryogenic coolant.


Application of conventional fluids create some techno-environmental problems such as,
Environmental pollution due to chemical dissociation or break up due to high cutting temperature.
Biological (Dermatological) problems to operators coming in physical contact.
Water pollution & Soil contamination during disposal.
So, it is absolutely necessary to use an environmentally acceptable coolant in manufacturing industry.
For this purpose, liquid nitrogen as a cryogenic coolant has been explored.



Properties of N2
Triple point : 63.148 K
Normal Boiling Point :77.313 K
Critical Point : 126.19K
It is the most abundant gas, composes about four-fifths (78.03%) by volume of the atmosphere.
It is a colourless, odourless,tasteless and non-toxic gas.
These characteristics of liquid nitrogen have made it as a preferred coolant.
Cryogenic cooling approaches
Cryogenic cooling approaches in material machining could be classified into four groups
Cryogenic pre-cooling the of work piece.
Indirect cryogenic cooling.
Cryogenic spraying and jet cooling.
Cryogenic treatment.
Cryogenic pre-cooling the of work piece.
Here,aim is to cool work piece or chip to change properties of material from ductile to brittle because, the ductile chip material can become brittle when the chip temperature is lowered and become easy to dispose
This achieved by
Pouring the liquid nitrogen by continually onto the work piece.
Disadavatage of this method are,
High LN2 consumption
Dimensional changes may occur




Indirect cryogenic cooling
This method was also called conductive remote cooling.
Here,the aim is to cool the cutting point through heat conduction.
In this method, instead of tool tip, tool shank is cooled by LN2.
Hence,LN2 does not contact with the workpiece and it does not cause significant change in properties of the work piece , in addition, cooling effect is stable.
Disadvantages are : effect of this approach is highly dependent on
thermal conductivity of the cutting tool material,
the distance from the LN2 source to the
thickness.



Cryogenic spraying and jet cooling.
The objective in this method is to cool cutting zone,particularly tool–chip interface with liquid nitrogen by using nozzles.
Here,workpiece will constant temperature and not subject to dimensional inaccuracy and geometrical Distortion
this localised cryogenic cooling reduces the tool
face temperature, enhances its hardness, and so reduces its wear rate;
This approach also embrittles the chip by
cold temperature and bend the chip with the chip breaker.

This cryogenic machining approach eliminates the BUE problem on tools because the cold temperature reduces the possibility of chips welding to the tool and the high pressure
cryogenic jet also helps to remove possible BUE formation
Therefore, it will produce better surface quality.
Cryogenic treatment
Cryogenic treatment is a process similar to heat treatment. In this method, samples are cooled down to cryogenic temperature and maintained at this temperaturefor a long time and then heated back to room temperature to improve wear resistance and dimensional stability of them.
However, the effect of the cryogenic treatment on cutting performance is not stable for all machiningapplications and cutting conditions, and there was not seen a comparison between cryogenic treatment and other cryogenic cooling approaches.
Effects of the cryogenic cooling in machining processes
The effect of cryogenic cooling on tool wear and tool life
Tool wear decreases considerably And tool life increases around four times , for steels.
The effect of cryogenic cooling on surface roughness and dimensional deviation
In application of indirect cryogenic cooling, the surface
rough nesses of materials machined with LN2 cooling were
found to be much better than the surface roughness of
materials machined without LN2 cooling after the same
length of cutting.
The effect of cryogenic cooling on friction
LN2 lubricated contact produced lower friction coefficient than the dry sliding contact and the emulsion-lubricated contact.


The effect of cryogenic cooling on cutting forces
Energy consumption in a cutting operation was associatedwith friction and cutting forces. So, it is significant being cutting forces less in terms of productivity and production cost in any machining process.
According to some researchers, cryogenic cooling did not significantly alter the cutting forces in machining of different materials.



CONCLUSION
When compared with dry cutting and conventional cooling, the most considerable characteristics of the cryogenic cooling application in machining operations
could be determined as enabling substantial improvement in tool life and surface finish-dimensional accuracy through reduction in tool wear through control of machining temperature desirably at the cutting zone.


REFERENCES
Yakup Yildiz, Muammer Nalbant, A review of cryogenic cooling in machining processes,2008
N.R.Dhar,S.Paul,A.B.Chattopadhyay,“Machinig of AISI 4041 steel under croygenic cooling –Tool wear, surface roughness, dimensional variation”,2002
Cryogenic Engineering, Thomas M. Flynn
Post: #2
sir, cryogenic cooling in machining process ppt and report send me
Post: #3

Refrigeration applications in machining operations play a very important role and many operations can not be performed efficiently without refrigeration. The application of a refrigerant in a cutting process can increase tool life and dimensional accuracy, reduce cutting temperatures, surface roughness and the amount of energy consumed in a metal cutting process and thus improve the productivity. In this article, liquid nitrogen, as cryogenic refrigerant, was investigated in detail in terms of methods of application in material removal operations and their effects on the cutting tool and the properties of the work piece material, shear temperature, Wear / friction and shearing forces. As a result, cryogenic cooling has been determined as one of the most favourable method for material cutting operations because it is capable of considerably improving the life of the tool and the surface finish by reducing the wear of the tool by controlling The machining temperature desirably in the cutting zone.

The use of cryogenic refrigerant in metal cutting has received renewed attention recently because liquid nitrogen is a safe, clean and non-toxic refrigeration liquid that does not require costly removal and can substantially improve the life of the tool.This work investigates the Effectiveness of the cryogenic refrigerant during Ti turning (125m / min, 48.5cm 3 / min) with different combinations of feeding speed and depth of cut. It is found that the greatest improvement in tool life using cryogenic refrigerant occurs under conditions of high temperature Federated and low depth of cut combinations. However, this combination of machining parameters produces much shorter tool life compared to low federate and high depth cutting combination.It is found that preventing heat generation during cutting is much more advantageous to extend tool life rather than Try to eliminate Heat with cryogenic refrigerant Although the cryogenic refrigerant is effective in the extraction of heat from the cutting area, it is proposed that the cryogenic refrigerant can limit the heat of friction generated during the cut and limit the heat transfer to the tool reducing The contact length of the tool. Refrigerant over the shear forces and morphology of the chip is also examined.
 

Marked Categories : cryogenics cutting ppt, coolant in machining operation pdf, project report on machine tools life increment by the use of cryo treatment, cryogenic machining process, cooling options for machining operations, crogenic presentation by kulkarni, project report on cryogenic cooling in machine tool, cryogenic jet machining process, cryogenic cooling in machining processes, cryogenic coolant, improvement of tool life by cryogenic cooling seminar, machining operation with coolant pdf, ppt on cryogenic cooling, cryogenic machining pdf, cryogenic cooling in machining, cooling processes for cutting, cryogenics ppt chemical seminar topic, machining operations and wear,

[-]
Quick Reply
Message
Type your reply to this message here.

Image Verification
Image Verification
(case insensitive)
Please enter the text within the image on the left in to the text box below. This process is used to prevent automated posts.

Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  fabrication of cooling tower with power generation systems paper Guest 1 327 14-10-2017 01:31 PM
Last Post: jaseela123
  absorbtion system for cooling purpuse by using exhaust gases of vehicle Guest 1 326 14-10-2017 09:30 AM
Last Post: jaseela123
  gas turbine blade cooling seminar report pdf Guest 1 435 13-10-2017 01:47 PM
Last Post: jaseela123
  be project on gear noise reduction by new approaches in gear finishing processes Guest 1 172 10-10-2017 02:16 PM
Last Post: jaseela123
  seminar report on advanced welding processes Guest 1 162 10-10-2017 12:37 PM
Last Post: jaseela123
  advanced cooling sysytem Guest 1 308 10-10-2017 11:27 AM
Last Post: jaseela123
  advanced cooling sysytem Guest 1 142 10-10-2017 11:27 AM
Last Post: jaseela123
Wink unconventional machining processes book pdf Guest 1 178 10-10-2017 10:57 AM
Last Post: jaseela123
Wink abrasive jet machining ppt Guest 1 224 07-10-2017 01:10 PM
Last Post: jaseela123
  seminar ppt for vibration assisted machining in turning Guest 1 216 04-10-2017 03:24 PM
Last Post: jaseela123
This Page May Contain What is Cryogenic cooling in machining processes And Latest Information/News About Cryogenic cooling in machining processes,If Not ...Use Search to get more info about Cryogenic cooling in machining processes Or Ask Here

Options: