Important: Use custom search function to get better results from our thousands of pages

Use " " for compulsory search eg:"electronics seminar" , use -" " for filter something eg: "electronics seminar" -"/tag/" (used for exclude results from tag pages)

Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Post: #1


.pdf  KLEIN VALVES.pdf (Size: 144.69 KB / Downloads: 58)


For Safety reasons, it is important to take the following precautions
before working on the valve:
1. Klein Slurry Valves are not to be used as an end of line
service valve.
2. Ensure that the procedures below meet or agree with the
site procedures if not review with your site safety officers.
3. Personnel making any adjustments to the valve should
utilise equipment and clothing normally used to work with
the process where the valve is to be installed.
4. The line must be depressurised, drained and vented
before installing or working on the valve.
5. Handling & installation of all valves, operators and
actuators must be carried out by personnel trained in all
aspects of installation and manual/mechanical handling
techniques using site occupational health and safety
6. Ensure the valve pressure/temperature limitations
marked on the nameplate are above or equal to the
service conditions.

Storage Instructions

The valves discs, seats, stems and end connections should be
adequately protected against damage. The protective end covers
should not be removed until ready for installation.
For long term storage of Klein valves the manufacturer would
recommend the following procedures be adopted:


The internals of valve are to be sprayed with a moisture
exclusion/corrosion inhibitor material. To achieve this, wearing
the correct protection equipment and dress, remove inlet end
covers and open valve by rotating wrench and direct the
atomized spray mist into the open valve cavity. Spray around
seat and disc and close valve. Spray onto stem and yoke
bush. Reseal the end covers.


Valves to be cycled every three months. The cycle operation
should be to the full open then to the full closed position.


All valves should be stored in the fully closed position End
protection caps or covers should remain on the valve at all


The preferred direction of flow for K4050, K4100 and K4150 Klein
valves is from the lower port below the disc, exiting from the side
port. Gaskets are required to fit between valve flanges and pipeline.
Check gaskets are suitable for duty.

Line Installation

Caution should be exercised to prevent damage of the valve sealing
mechanism during installation. The following steps will assist in
complying with the correct installation procedure.
Remove the protective end covers prior to installation. The gasket
faces should be wiped with clean solvent to ensure gasket faces
are clean.
Substantial supports should be provided for the free ends of the
pipeline and for the valve during installation. Unsupported pipelines
hung from valves can cause high stress in valve body leading to
possible damage.
For K4100 valves where the mating component has been removed
from the remainder of the valve, the disc should be in the closed
position before refitting to the installed mating component. This will
allow the disc to hold the seat in the correct position to ensure the
valve will seal after refitting the mating component.
Where possible, leave valve in `open’ position until entire
construction work has been completed, pipeline cleaned and plant
is ready for start up.

Testing Installations

When pipeline or vessel installations are being tested it is desirable
to have all Valves in the `open’ position. DO NOT USE Klein Valves
as Block Valves when testing pipelines or vessels as foreign matter
may seriously damage sealing mechanism. Should valves be used
for such testing, the Manufacturer takes NO RESPONSIBILITY for
any damage which may affect the valves sealing mechanism and all
Guarantees are withdrawn. If the user decides to test such
installations with the valves `closed’, caution should be exercised to
ensure that the sealing mechanism is not subjected to pressure
differentials in excess of the maximum operating pressure of the
valve seat design.
Post: #2
can you pls send full seminar report about klein valve

Marked Categories : klein valves ppt download, klein valves, where can i find klein valve,

Quick Reply
Type your reply to this message here.

Image Verification
Image Verification
(case insensitive)
Please enter the text within the image on the left in to the text box below. This process is used to prevent automated posts.

Possibly Related Threads...
Thread: Author Replies: Views: Last Post
Smile Ball Valves with Pneumatic and Electrical Actuators Sudeenggproducts 1 320,038 21-09-2017 02:51 PM
Last Post: jaseela123
  SCADA and Control Valves ppt study tips 1 1,101 14-09-2017 12:09 PM
Last Post: jaseela123
  Globe valves computer science crazy 0 10,467,776 25-08-2017 09:32 PM
Last Post: computer science crazy
  Globe valves Computer Science Clay 0 4,630,963 25-08-2017 09:32 PM
Last Post: Computer Science Clay
  failure analysis of ic engine valves Guest 1 246 10-08-2017 12:38 PM
Last Post: jaseela123
  engine valves manufacturing process pdf Guest 1 0 08-04-2017 02:45 PM
Last Post: jaseela123
  Leader Valves Limited mkaasees 0 0 23-09-2016 11:16 AM
Last Post: mkaasees
  Two Stroke Engine Using Reed Valves presentation Abstract 0 484 02-06-2015 04:20 PM
Last Post: presentation Abstract
  lab evaluation of pilot gaslift valves of m s camlow make for field applications subine 0 77 25-10-2014 02:38 PM
Last Post: subine
  probe testing of gaslift valves and significance in field applications subine 0 87 25-10-2014 02:32 PM
Last Post: subine
This Page May Contain What is KLEIN VALVES And Latest Information/News About KLEIN VALVES,If Not ...Use Search to get more info about KLEIN VALVES Or Ask Here