Important: Use custom search function to get better results from our thousands of pages

Use " " for compulsory search eg:"electronics seminar" , use -" " for filter something eg: "electronics seminar" -"/tag/" (used for exclude results from tag pages)


Tags: Pls can u make a ppt of it,
 
 
Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
ppt on seminar of aluminium casting process making piston
Post: #1

MANUFACTURING PROCESS OF A PISTON



INTRODUCTION

A piston is an important component of reciprocating engine helps to convert energy obtained by the combustion of fuel in cylinder into useful mechanical power.
It is like a disc which reciprocates within a cylinder.
It is either moved by the fluid or it moves the fluid which enters the cylinder.

PISTON IN IC ENGINE

The main purpose of the piston of an internal combustion engine is to transfer force from expanding gas in the cylinder to the crankshaft through a connecting rod.
It is located in a cylinder and is equipped with piston rings to provide a good seal between the cylinder wall and piston.

MANUFACTURING PROCESS

Casting
Heat treatment
Machining process
Pin fitting and Inspection

CASTING

The foundry is the beginning of the piston.
At the foundry the die is prepared by heating it to operating temperature for approximately one hour.
This process allows the die to readily accept the molten material when it is poured.
The molten material used for Piston is 10% Silicon content Aluminium or Aluminium alloys.

PROCESS

The process starts by heating the material to 700 degrees Celsius.
The material is then scooped up with a ladle from the crucible (the pot that holds the molten material).
This is then poured into the die through the sprue.
The material is then allowed to cool before it is removed from the die.

MACHINING PROCESS

Open end bore machining
Rough outer diameter turning
Grooves forming
Semi finish hole boring
Circlip grooving oil hole drilling in 3rd groove and skirt
Ring grooving and chamfering
Final outer diameter turning
Deburring and cleaning
Tin coating
Finish pin hole boring

CNC TURNING

Turning of the casting is carried out on CNC machinery.
This equipment is the most accurate and fastest available for this application with very tight tolerances and extremly fast spindle speeds. The following operations are performed on this machine:
Open end bore machining
Rough outer diameter turning
Grooves forming

REAMING

The final machining process for the piston is that of reaming.
This process involves the piston being placed in a bath of oil and reamed at different sizes to reach the final size required.
Since the pin boring process is only rough it is necessary to ream the pin bore a number of times to achieve the surface finish and size required.

DEFECTS

Since it’s a main reciprocating part of engine and hence it creates the problems of unbalancing due to its inertia.
Due to friction between wall of the cylinder and piston rings its life becomes short and it generates the unpleasant sound due reciprocating mechanism.
To transmit the energy of reciprocating piston, it is connected to a connecting rod and crank mechanism and due to these parts there occurs mechanical losses.
The motion of the crank shaft is not smooth, since energy supplied by the piston is not continuous and it is impulsive in nature.
To supply the fuel into the cylinder there is need of the valves and valve mechanism and during opening and closing of the valves, mechanical noise occurs and also mechanical vibration.

CONCLUSION

Although the piston appear to be a simple part, it is actually quite complex from the design and manufacturing stand point.
The efficiency and economy of the engine primarily depends on the working of the piston. So the working of the piston be more efficient.
It must operate in the cylinder with minimum friction and should be able to withstand the high explosive force developed in the cylinder and also withstand very high temperature ranging from 2000 C to 2800 C during operation.
To avoid the wear and unpleasant sound between cylinder walls and piston rings, piston rings should manufactured with wear resistant materials like cast iron and steel.
Lubrication problems should b avoided between cylinder walls n piston by providing oil grooves accurately.
Finally, the piston should be as strong as possible, however, its weight should be minimized as far as possible in order to reduce the inertia due to its reciprocating mass
Post: #2
It can be understood in the following video:


 

Marked Categories : rough outer turning on piston,

[-]
Quick Reply
Message
Type your reply to this message here.

Image Verification
Image Verification
(case insensitive)
Please enter the text within the image on the left in to the text box below. This process is used to prevent automated posts.

Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  abstract of ieee seminar paper on bionic eye Guest 3 199 Yesterday 09:20 PM
Last Post: SharonJer
  seminar abstract for laser communication Guest 2 0 20-01-2018 06:55 AM
Last Post: Austinfloro
  Ultrasonic Trapping In Capillaries For Trace-Amount Bi (Download Full Seminar Report) Computer Science Clay 2 6,523,288 17-01-2018 11:59 AM
Last Post: dhanabhagya
  MANUFACTURING PROCESS OF A PISTON ppt study tips 2 7,098 17-01-2018 10:51 AM
Last Post: dhanabhagya
  8K High Resolution Camera System : Seminar Report and PPT seminar projects maker 4 2,861 14-01-2018 11:08 PM
Last Post: yaswanth reddy gundra
  Metal Casting and Foundry seminar flower 2 1,184 12-01-2018 10:50 AM
Last Post: dhanabhagya
  Biometrics Security System Full Download Seminar Report and Paper Presentation computer science crazy 29 56,405,594 08-01-2018 05:23 PM
Last Post: Raymondnof
  seminar topics on e learning pdf Guest 1 0 08-01-2018 10:31 AM
Last Post: dhanabhagya
  seminar abstract of bicomputers Guest 1 148 08-01-2018 10:23 AM
Last Post: dhanabhagya
  seminar report on rotating tower download pdf Guest 1 0 18-12-2017 10:15 AM
Last Post: jaseela123
This Page May Contain What is ppt on seminar of aluminium casting process making piston And Latest Information/News About ppt on seminar of aluminium casting process making piston,If Not ...Use Search to get more info about ppt on seminar of aluminium casting process making piston Or Ask Here

Options: