Important: Use custom search function to get better results from our thousands of pages

Use " " for compulsory search eg:"electronics seminar" , use -" " for filter something eg: "electronics seminar" -"/tag/" (used for exclude results from tag pages)

Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Post: #1


.docx  SINGLE PHASE CYCLO CONVERTER.docx (Size: 15.79 KB / Downloads: 60)


To verify the operation of single phase Cyclo Converter with R and RL Loads and to
observe the output and input waveforms


1. I-φ Center tapped
2. I-φ Cyclo Converter power
circuit with firing unit
3. Rheostat 1
4. Inductive load 1
5. Voltmeter(MI) 1
7. CRO with (1:10) Probe 1
8. Patch cards 1 set


The circuit diagram of 1-φ cyclo converter with R and RL load are shown in fig.
Construction ally there are four SCR’s T1, T2, T3 &T4.Out of them T1, T2 are responsible for
generating positive halves forming the positive group. The other two T3, T4 are responsible for
negative haves forming negative group. This configuration and waveforms are shown for ½ and
1/3 of the supply frequency. Natural commutation process is used to turn off the SCR’s.
A) For R-Load: During the half cycle when point A is positive with respect to O, SCR T1 is
in conducting mode and is triggered at wt =α then current flows through positive point
A-T1-load-negative O. In the negative half cycle when B point is positive with respect to
the point O,SCR T1 is automatically turned off due to natural commutation and SCR T2 is
triggered at wt = π+α. In this condition the current flows through B-T2-load-O.
) For RL-Load:-
When A is positive with respect to O forward biased SCR T1 is triggered at wt=α and the
current start to flow through A-T1-R-L-O. Load voltage becomes zero at wt=π but load
current will not become zero at this angle due to inductance. It becomes zero at wt =β
which is called extinction angle. So it is naturally commutated at wt=β. After half cycle
point B positive with respect to point O. Now at angle wt=π+α. T2 is triggered and the load
current takes path from B-T2-R-L_o and its direction is positive as in the previous case.
The load current decays zero at wt =π+β and SCR T2 is naturally commutated.
In the half cycle when O is positive with respect to B point, T4 is triggered instead of T1
at an angle of wt= (2π+α). Now the load current flows through O-L-R-T4-B but the
direction of load current reversed. When the load current becomes zero at an angle wt=
(2π+α) , T4 naturally commutated because the voltage is already reversed at wt = 3π.When
wt = (3π+α) and point O, is positive with respect to point A,T3 is triggered then the current
flows through O-L-R-T3-A , and the direction of load current is same in previous case. In
the next half cycle again T1 will triggered like this we get one cycle of output frequency for
two cycles of input frequency, when the frequency division switch is at 2.


A) For R-Load:

1. Connect the circuit as shown in figure.
2. Verify the connections from the lab instructor before switch on the supply.
3. Keep the rheostat position value given by the lab instructor
4. Switch ON the supply and note down the frequency of input voltage from the
5. Set the frequency division switch at 2 and note the readings of time period of
output voltage waveform for different set of firing angles
6. Calculate the practical value of output frequency by reciprocating the value of
time period and theoretical value of frequency will be found from frequency
division setting

Marked Categories : theory on rl loads, cycloconverter with r load theory, instruction and operation of single phase tosingle phase cycloconverter pdf file, single phase cycloconverter ppt, theory for single phase cycloconverter, single phase cyclo conver with r and rl load diadgam, singlephase cycloconverter with r and rl load, theory on single phase cyclo converter with r and rl load, single phase cyclo convertor with r rl, single phase cycloconverter with r and rl load theory, verify the voltage waveform of single phase cycloconverter with r load, ppt on cycloconverter single phase, single phase cycloconverter with r and rl load, cyclo converter with r and rl load,

Quick Reply
Type your reply to this message here.

Image Verification
Image Verification
(case insensitive)
Please enter the text within the image on the left in to the text box below. This process is used to prevent automated posts.

Possibly Related Threads...
Thread: Author Replies: Views: Last Post
Rainbow word to ieee paper format converter Guest 1 212 17-11-2017 12:31 PM
Last Post: jaseela123
  catalytic converter seminar report Guest 1 0 07-11-2017 09:51 AM
Last Post: jaseela123
  single phase cyclo converter Guest 1 0 25-10-2017 12:13 PM
Last Post: jaseela123
  literature review on 3 phase automatic changeover switch pdf Guest 1 0 25-10-2017 11:41 AM
Last Post: jaseela123
Thumbs Down five phase brushless dc machine direct drive system seminar ppt download Guest 1 258 14-10-2017 09:42 AM
Last Post: jaseela123
  word to ieee paper format converter Guest 1 149 13-10-2017 01:39 PM
Last Post: jaseela123
  converter faults and protection in hvdc systems ppt Guest 1 188 12-10-2017 11:01 AM
Last Post: jaseela123
  microcontroller based automatic single phase preventer project download Guest 1 0 11-10-2017 10:10 AM
Last Post: jaseela123
  single line diagram of 33kv garividi substation Guest 1 194 10-10-2017 02:36 PM
Last Post: jaseela123
Photo developed 3 phase inverter circuit in multisim download Guest 1 166 10-10-2017 11:04 AM
Last Post: jaseela123
This Page May Contain What is SINGLE PHASE CYCLO CONVERTER WITH R & RL LOADS And Latest Information/News About SINGLE PHASE CYCLO CONVERTER WITH R & RL LOADS,If Not ...Use Search to get more info about SINGLE PHASE CYCLO CONVERTER WITH R & RL LOADS Or Ask Here