Important: Use custom search function to get better results from our thousands of pages

Use " " for compulsory search eg:"electronics seminar" , use -" " for filter something eg: "electronics seminar" -"/tag/" (used for exclude results from tag pages)

Tags: soil, nailing, full, report, soil nailing, soil nailing ppt, soil nailing pdf, soil nailing india, soil nailing contractors, soil nailing design, soil nailing procedure, soil nailing case study, soil nail retaining wall, soil nail wall, soil nailing specification,
Thread Rating:
  • 1 Votes - 4 Average
  • 1
  • 2
  • 3
  • 4
  • 5
soil nailing full report
Post: #1

.pptx  SOIL NAILING PPT.pptx (Size: 564.75 KB / Downloads: 893)



Soil Nailing is a procedure to reinforce and strengthen ground adjacent to an excavation by installing closely spaced steel bars called nails ,as construction proceeds from top down.

It is an effective and economical method of constructing retaining wall for excavation support, support of hill cuts, bridge abutments and high ways.

This process is effectively in cohesive soil, brocken rock, shale or fixed face conditions.


Soil nail technology was first used in France to build a permanent retaining wall cut in soft rock. The project, undertaken in 1961, was the first where steel nails were used to reinforce a retaining wall.

The first soil nail wall to use modern soil nailing techniques was built near Versailles in 1972. The technique included installing high-density, grouted soil nails into a 60-ft.-high wall and facing it with reinforced concrete.


Stabilization of railroad and highway cut slopes

Excavation retaining structures in urban areas for high-rise building and underground facilities

Tunnel portals in steep and unstable stratified slopes

construction and retrofitting of bridge abutments with complex boundaries involving wall support under piled foundations

Stabilizing steep cuttings to maximize development space.

The stabilizing of existing over-steep embankments.

Soil Nailing through existing concrete or masonry structures such as failing retaining walls and bridge abutments to provide long term stability without demolition and rebuild costs.

Temporary support can be provided to excavations without the need for bulky and intrusive scaffold type temporary works solutions

Driven Nails

Grouted Nails

Corrosion Protected Nails

Jet grouted Nails

Launched Nails

Driven nails

Generally small-diameter nails (15-46 mm) with a relatively limited length (to about 20 m) made of mild steel (about 50 ksi) that are closely spaced in the wall (two to four nails per square meter). Nails with an axial channel can be used to permit the addition of grout sealing. Driven nails are the quickest (four to six per hour) and most economical to install (with a pneumatic or hydraulic hammer).

Grouted Nails

Steel bars, with diameters ranging from 15 to 46 mm, stronger than driven nails (about 60 ksi). Grouted nails are inserted into boreholes of 10-15 cm and then cement-grouted. Ribbed bars are also used to increase soil adhesion.

Corrosion-protected nails

For aggressive soils as well as for permanent structures.

Jet-grouted nails

A composite of grouted soil and a central steel rod, up to 40 cm thick. Nails are installed using a high-frequency vibropercussion hammer, and cement grouting is injected during installation. This method has been shown to increase the pullout resistance of the composite, and the nails are corrosion-resistant.

Launched nails

Nails between 25 and 38 mm in diameter and up to 6 m or longer are fired directly into the soil with a compressed-air launcher. Used primarily for slope stabilization, this technique involves the least site disturbance


Drilling Equipments

Grout Mixing Equipments

Shotcreting / Guniting Equipments


Drilling Equipment

There are few common types of drilling equipment, namely rotary air-flushed and water-flushed, down-the-hole hammer, tri-cone bit. It is important to procure drilling equipment with sufficient power and rigid drill rods.

Grout Mixing Equipment

In order to produce uniform grout mix, high speed shear colloidal mixer should be considered. Powerful grout pump is essential for uninterrupted delivery of grout mix. If fine aggregate is used as filler for economy, special grout pump shall be used.

Shotcreting/Guniting Equipment

Dry mix method will require a valve at the nozzle outlet to control the amount of water injecting into the high pressurized flow of sand/cement mix. For controlling the thickness of the shotcrete, measuring pin shall be installed at fixed vertical and horizontal intervals to guide the nozzle man.


The compressor shall have minimum capacity to delivered shotcrete at the minimum rate of 9m3/min. Sometimes, the noise of compressor can be an issue if the work is at close proximity to residential area, hospital and school.


Steel Reinforcements

Grout Mix


Steel Reinforcements

For corrosion protection, all steel component shall be galvanized. If machine threading after galvanization is unavoidable, then proper zinc based coating shall be applied onto the thread. For double corrosion protection, the PVC corrugated pipe used shall be of good quality and adequate thickness. Preferably galvanized corrugated steel pipe shall be used.

Grout Mix

For conventional soil nail, the water cement ratio of the grout mix ranges from 0.4 to 0.5. As most cementitious grout will experience some grout shrinkage, non-shrink additive can be used to reduce breeding and grout shrinkage. The resistance at grout-soil interface of nail will significantly reduced when the grout shrink.


Shotcrete or gunite can be continuous flow of mortal or concrete mixes projected at high speed perpendicularly onto the exposed ground surface by means of pneumatic air blowing for dry mix or spraying for wet mix.

Initial excavation

This initial excavation will be carried out by trimming the original ground profile to the working platform level where the first row of soil nails can be practically installed. The pre-requisite of this temporary excavation shall be in such a way that the trimmed surface must be able to self support till completion of nail installation. Sometimes, sectional excavation can be carried out for soil with short self support time. If shotcrete/gunite is designed as facing element, the condition of the trimmed surface shall be of the satisfactory quality to receive the shotcrete

Drilling of holes

Drilling can be done by either air- flushed percussion drilling, auguring or rotary wash boring drilling depending on ground condition. The size of drilled hole shall be as per the designed dimension. Typically, the hole size can range from 100mm to 150mm. In order to contain the grout, the typical inclination of the drill hole is normally tilted at 15º downward from horizontal. Flushing with air or water before nail insertion is necessary in order to remove any possible collapsed materials, which can potentially reduce the grout- ground interface resistance.

Insertion of nail reinforcement and grouting

The nail shall be prepared with adequate centralizers at appropriate spacing and for proper grout cover for first defense of corrosion protection. In additional to this, galvanization and pre- grouted nail encapsulated with corrugated pipe can be considered for durability. A grouting pipe is normally attached with the nail reinforcement during inserting the nail into the drilled hole. The grouting is from bottom up until fresh grout return is observed from the hole. The normal range of water/cement ratio of the typical grout mix is from 0.45 to 0.5


With the right soil and site conditions, a rapid and economical means of constructing earth retention support systems and retaining walls.

Shorter drill holes.

Smaller diameter bars at shorter lengths.

Retaining walls are secured laterally into the soil, eliminating piles and foundation footers.

Grouting only once is required, saving time and labor.

The technique is flexible, easily modified.

Creates less noise and traffic obstructions.

Less impact on nearby properties

Allow in-situ strengthening on existing slope surface with minimum excavation and backfilling, particularly very suitable for uphill widening, thus environmental friendly,

Allow excellent working space in front of the excavation face,

Can be used for strengthening of either natural slope, natural or man- made cut slopes,


Nail encroachment to retained ground rendering unusable underground space,

Generally larger lateral soil strain during removal of lateral support and ground surface cracking may appear,

Tendency of high ground loss due to drilling technique, particularly at course grained soil,

Less suitable for course grained soil and soft clayey soil, which have short self support time, and soils prone to creeping,

Suitable only for excavation above groundwater


Since this process is effective in cohesive soil, broken rock, shale, or mixed face conditions it permits flexibility to conform to a variety of geometric shapes to meet specific site needs.
Due to its rather straightforward construction method and is relatively maintenance free, the method has gained popularity in India for highway and also hillside development projects. Soil nailing is an economical means of creating shoring systems and retaining walls.
Post: #2

.pdf  soil nailing.pdf (Size: 334.88 KB / Downloads: 532)
Soil Nailing for Slope Strengthening

Liew Shaw-Shong
Gue & Partners Sdn Bhd, Kuala Lumpur, Malaysia

Passive soil nailing technique has gained popularity for temporary and permanent slope
strengthening works at both in-situ cut slopes of virtually any formations and also man-made filled slopes in
Malaysia. However, there are still many misconception and myth in the design and construction of soil
nails. Various design and construction practices have been adopted in the local industry of soil nailing
works. This paper presents some of the common conventional design and construction practices in detail.
Post: #3
Presented by:
Salem Babtain

.ppt  soil nailing presentation.ppt (Size: 10.18 MB / Downloads: 579)
Soil nailing is a technique in which soil slopes, excavations or retaining walls are reinforced by the insertion of relatively slender elements - normally steel reinforcing bars.
Literature Review
New Austrian Tunneling Method" (NATM), in which grouted rock bolts and shotcrete were used for supporting tunnels
permanent support of retaining walls in a cut in soft rock in France.
The use of grouted "soil nails" and driven soil nails, which consist of solid steel bars and steel angle iron, continued to grow in the 1970's, in France, Germany and north America
The first wall built in France using current soil nail techniques was reported to have been built by Soletanche, in Versailles
Guidelines and Manuals
One of the first national guideline publications for soil nailing. ( In Japan)
 in France (Clouterre Program)
 $ 5 million study to develop design methodology for soil nail walls
 "Recommendations of Clouterre," published in 1991
 Federal Highway Administration published its "Manual for Design and Construction of Soil Nail Walls.“
Slope Failure
What is slope failure ?

The slope can not support itself
- Gravitational and seepage forces cause disturbing force
- Soil friction provide resisting force
- If disturbing moment > resisting moment Slope will failure
Soil uses
Soil nailing is used to reinforce
-tunnels wall support
-soil cut slopes
-retaining wall support
-disturbed terrain and
-natural hillsides stabilize
Principle of Soil nailing
In slope stability calculations, the result needs to obviously ensure that the resisting forces are greater than the force tending to cause slope failure.
Factor of Safety ( FOS )
FOS is defined as the ratio of total resisting forces to total disturbing forces or total overturning moment

Marked Categories : soil nail, soil nailing ppt download, seminar report on reinforced earth walls, ppt files on civil eng adminstration, soilnailinginindia, percussive soil nailing techniques, soil nail sand facing french, shotcrete technology in civil engineering ppt, slope design di lumpur ppt, terminology used for drilling of ppt file in civil, a case study of construction of earth retaining wall in highway india pdf format, soil nailing, ppt on soil nailing technique, soil nailing projects, civil engineering seminar topic soil nailing, soil nailing techniques, soil nailing in india, soil nailing ppt, ppt on backfill and reinforced material, cost of soil nail wall in india,

Quick Reply
Type your reply to this message here.

Image Verification
Image Verification
(case insensitive)
Please enter the text within the image on the left in to the text box below. This process is used to prevent automated posts.

Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  Mini project report on SHADOW ALARM project girl 6 11,060 Yesterday 02:07 PM
Last Post: Austinfloro
  water cooler project report Guest 2 0 Yesterday 10:21 AM
Last Post: Guest
  hydroforming full report project report tiger 5 25,280,105 19-01-2018 01:37 AM
Last Post: Guest
  nrega project report er diagram Guest 1 0 18-01-2018 03:31 PM
Last Post: dhanabhagya
  COST EFFECTIVENESS OF MINERAL WOOL INSULATION Vs PERLITE INSULATION full report project report tiger 2 11,828,426 18-01-2018 11:53 AM
Last Post: dhanabhagya
  Solar pond technology full report seminar girl 2 782 18-01-2018 10:08 AM
Last Post: dhanabhagya
  suggestion for informative report of public deposits invited by company Guest 1 0 18-01-2018 10:06 AM
Last Post: dhanabhagya
  Ultrasonic Trapping In Capillaries For Trace-Amount Bi (Download Full Seminar Report) Computer Science Clay 2 6,460,769 17-01-2018 11:59 AM
Last Post: dhanabhagya
  fuel from plastic waste full report seminar presentation 25 97,589,441 17-01-2018 10:40 AM
Last Post: dhanabhagya
  nanorobotics full report project topics 24 76,235,645 16-01-2018 05:50 PM
Last Post: Guest
This Page May Contain What is soil nailing full report And Latest Information/News About soil nailing full report,If Not ...Use Search to get more info about soil nailing full report Or Ask Here