Important: Use custom search function to get better results from our thousands of pages

Use " " for compulsory search eg:"electronics seminar" , use -" " for filter something eg: "electronics seminar" -"/tag/" (used for exclude results from tag pages)

Thread Rating:
  • 0 Votes - 0 Average
  • 1
  • 2
  • 3
  • 4
  • 5
Post: #1


.pptx  all presentation.pptx (Size: 1.89 MB / Downloads: 172)

3-Phase Induction Motors Introduction
• 3-phase induction motors
are simple, low cost,
and easy to maintain.
• They run at essentially
constant speed from
zero-to-full load.
• Therefore, they are the
motors most frequently
encountered in industry.

Induction Motor Components
A 3-phase induction motor has two main parts:
• A stator – consisting of a steel frame that supports a hollow,
cylindrical core of stacked laminations. Slots on the internal.

• A rotor – also composed of punched laminations, with rotor slots for
the rotor winding.

Induction Motor Components
Squirrel cage rotor consists
of copper bars, slightly
longer than the rotor,
which are pushed into the
The ends are welded to
copper end rings, so that
all the bars are short
In small motors, the bars
and end-rings are diecast
in aluminium to form
an integral block.

Induction Motor Components
A wound rotor has a 3-phase winding, similar to the stator winding.
The rotor winding terminals are connected to three slip rings which turn with the rotor. The slip rings/brushes allow external resistors to be connected in series with the winding.
The external resistors are mainly used during start-up –
under normal running conditions the windings shortcircuited
Induction Motor: Operating principle

The following sequence of events takes place:

1. A voltage E = BLv is induced in each conductor while it is being cut by the Flux (Faraday’s Law)
2. The induced voltage produces currents which circulate in a loop around the conductors (through the bars).
3. Since the current-carrying conductors
lie in a magnetic field, they experience a mechanical force (Lorentz force).
4. The force always acts in a direction to
drag the conductor along with the
magnetic field.
Induction Motor – Rotating Field: Direction of rotation
The phase current waveforms
follow each other in the
sequence A-B-C.
This produces a clockwise rotating
magnetic field.
If we interchange any two of the
lines connected to the stator,
the new phase sequence will
be A-C-B.
This will produce a counter clockwise rotating field,
reversing the motor direction.

Post: #2
Electrical Machines

.pdf  1Electrical Machines.pdf (Size: 139.25 KB / Downloads: 104)
Induction Machines


The induction machine was invented by NIKOLA TESLA in 1888. Right from its incep-
tion its ease of manufacture and its robustness have made it a very strong candidate for
electromechanical energy conversion. It is available from fractional horsepower ratings to
megawatt levels. It finds very wide usage in all various application areas. The induction
machine is an AC electromechanical energy conversion device. The machine interfaces with
the external world through two connections (ports) one mechanical and one electrical. The
mechanical port is in the form of a rotating shaft and the electrical port is in the form of
terminals where AC supply is connected. There are machines available to operate from three
phase or single phase electrical input. In this module we will be discussing the three phase
induction machine. Single phase machines are restricted to small power levels.
Post: #3
Electrical Machines

.pdf  1Electrical Machines.pdf (Size: 285.8 KB / Downloads: 134)

Testing of Transformers

The structure of the circuit equivalent of a practical transformer is developed earlier.
The performance parameters of interest can be obtained by solving that circuit for any load
conditions. The equivalent circuit parameters are available to the designer of the transformers
from the various expressions that he uses for designing the transformers. But for a user
these are not available most of the times. Also when a transformer is rewound with different
primary and secondary windings the equivalent circuit also changes. In order to get the
equivalent circuit parameters test methods are heavily depended upon. From the analysis of
the equivalent circuit one can determine the electrical parameters. But if the temperature
rise of the transformer is required, then test method is the most dependable one. There are
several tests that can be done on the transformer; however a few common ones are discussed

Winding resistance test

This is nothing but the resistance measurement of the windings by applying a small
d.c voltage to the winding and measuring the current through the same. The ratio gives
the winding resistance, more commonly feasible with high voltage windings. For low voltage
windings a resistance-bridge method can be used. From the d.c resistance one can get the
a.c. resistance by applying skin effect corrections.

Polarity Test

This is needed for identifying the primary and secondary phasor polarities. It is
a must for poly phase connections. Both a.c. and d.c methods can be used for detecting
the polarities of the induced emfs. The dot method discussed earlier is used to indicate the
polarities. The transformer is connected to a low voltage a.c. source with the connections
made as shown in the fig. 18(a). A supply voltage Vs is applied to the primary and the
readings of the voltmeters V1, V2 and V3 are noted. V1 : V2 gives the turns ratio. If V3 reads
V1−V2 then assumed dot locations are correct (for the connection shown). The beginning and
end of the primary and secondary may then be marked by A1 −A2 and a1 −a2 respectively.
If the voltage rises from A1 to A2 in the primary, at any instant it does so from a1 to a2 in
the secondary. If more secondary terminals are present due to taps taken from the windings
they can be labeled as a3, a4, a5, a6. It is the voltage rising from smaller number towards
larger ones in each winding.

Marked Categories : sriram amilkanthwar, seminar papers on electrical machines, seminar on electric machine, seminar topicson electrical machines, project of electrical machine, seminars for electrical machines, electrical seminar related to small low cost induction motorsmotors, electrical machines, sminar about electrical machines, electrical mechinary semenar projects, electrical machines latest, latest seminar topics on electric machines, seminar paper about electrical machines of 2012, seminar topics in electrical machine, seminar on electrical machines, seminars on electrical machines, latest seminar topics for electrical machines 2012, seminar on electrical machine,

Quick Reply
Type your reply to this message here.

Image Verification
Image Verification
(case insensitive)
Please enter the text within the image on the left in to the text box below. This process is used to prevent automated posts.

Possibly Related Threads...
Thread: Author Replies: Views: Last Post
  information about automatic machines for 11th o c project Guest 2 1,120 04-03-2018 05:54 PM
Last Post: Guest
  electrical bit bank pdf Guest 1 181 18-11-2017 10:02 AM
Last Post: jaseela123
  previous year paper for sdo exam of electrical in haryana Guest 1 263 18-11-2017 10:01 AM
Last Post: jaseela123
  industrial visit for electrical companies in trivandrum Guest 1 0 18-11-2017 09:56 AM
Last Post: jaseela123
  ppt for iocl electrical engineering Guest 1 0 18-11-2017 09:30 AM
Last Post: jaseela123
  ee2403 special electrical machines book ppt format Guest 1 533 17-11-2017 01:19 PM
Last Post: jaseela123
  electrical resistivity prospecting for groundwater Guest 1 0 14-10-2017 02:45 PM
Last Post: jaseela123
  Best Deals On Sewing Machines Guest 1 166 14-10-2017 12:38 PM
Last Post: jaseela123
  electrical balance of plant definition Guest 1 158 14-10-2017 11:58 AM
Last Post: jaseela123
  magnetic materials used in electrical machines instruments and relays Guest 1 216 13-10-2017 12:58 PM
Last Post: jaseela123
This Page May Contain What is ELECTRICAL MACHINES And Latest Information/News About ELECTRICAL MACHINES ,If Not ...Use Search to get more info about ELECTRICAL MACHINES Or Ask Here